Skip to content
IndustrialImaging

Published November 18, 2026

CWI inspection cost per hour, per visit and per project

A Certified Welding Inspector from a US inspection agency typically bills $75 to $125 per hour, with a 2 to 4 hour minimum per visit plus mileage, and $700 to $1,100 per 10 hour day on plant and shutdown work. A full structural steel special inspection package on a small two story frame usually lands between $8,000 and $25,000. The hourly rate matters less than how many trips you trigger, whether the work is continuous or periodic, and how many welds fail and need a second visit.

CWI inspection cost per hour, per visit and per project

CWI and weld inspection prices by job type

Ranges for US inspection agencies and independent CWIs, for budgeting before you request quotes.

JobTypical US priceWhat moves it
CWI hourly rate, straight time $75 to $125 per hour Region, ICC certifications on top of CWI, union or prevailing wage
Overtime, Saturday and night work 1.5 times the hourly rate Shift length, weekend erection
Trip minimum 2 to 4 hours per visit Agency policy, distance
CWI day rate on plant or shutdown work $700 to $1,100 per 10 hour day Per diem, travel, site safety training
Shop inspection at a fabricator $75 to $125 per hour plus travel Shop location, whether the fabricator is AISC certified
UT technician for CJP welds $90 to $150 per hour Level II or III, AWS D1.1 Clause 8 qualification
MT on fillet welds $85 to $130 per hour Number of locations per visit
Mileage $0.60 to $0.90 per mile Round trip from the agency office
Daily reports and final letter Included, or $150 to $500 per project Agency policy

These are planning ranges, not quotes. A public reference point is the Utah Division of Facilities Construction and Management, which publishes the contracted rates it pays for code special inspections, including CWI time, in its 2026 special inspections rate schedule. For the service itself, scope and the code tasks a CWI covers, see our structural steel inspection services page.

Worked budget for a two story steel frame

Take a two story office building, Risk Category II, about 180 tons of steel, 40 moment connections with two CJP flange welds each (80 CJP welds), bolted braced frames, composite deck with shear studs, and an AISC certified fabricator. Field welding runs about 10 working days.

  • Continuous CWI during CJP field welding. 10 days at 8 hours and $95 per hour, about $7,600.
  • UT of CJP welds at the 10 percent Risk Category II rate. Eight welds, one visit at a 4 hour minimum and $120 per hour, about $480.
  • Periodic bolting inspection. Six visits at 3 hours and $90 per hour, about $1,620.
  • Deck welds and shear studs. Three visits at 3 hours and $90 per hour, about $810.
  • Shop inspection. Waived by the building official because the fabricator is AISC certified, $0.
  • Repair reinspections. Four short visits at a 2 hour minimum and $95 per hour, about $760.
  • Mileage. 23 round trips of 40 miles at $0.70, about $640.
  • Daily reports and the final letter to the building official, about $300.

That gives roughly $12,200. Change one input and the number moves fast. On a Risk Category III school with the same frame, AISC 360 requires UT of every CJP weld, so the UT line grows to about three days at $120 per hour, and the total passes $14,500. If the fabricator is not certified and sits two states away, shop inspection with travel and per diem can add $4,000 to $8,000 on its own.

What moves a CWI inspection quote

Trips drive cost more than hours. A 30 minute bolt check still pays the 2 to 4 hour minimum and the mileage, so a schedule that calls the inspector out for every small task can double the bill. Ask the erector to group periodic tasks, such as bolting, deck welds and studs, into planned visits, and give the agency the 24 hour notice most contracts require so you avoid premium call out charges.

Continuous tasks are the next big line. Many statements of special inspections list CJP groove welds and demand critical welds as continuous, which keeps a CWI on site for the whole shift. The engineer of record sets those frequencies. You cannot negotiate them with the agency, but you can sequence the welding so that field CJP work happens on consecutive days instead of scattered half days.

Rejection rate is the third. Every failed weld means a repair, a second visual check and often a repeat UT. Most contracts put that cost on the steel contractor, so write it into the subcontract before the first column goes up. A fabricator with a good welding program and preheat discipline can save more than the gap between the cheapest and the most expensive agency.

CWI cost on plant, pipe and shutdown jobs

Outside building construction, CWIs are bought by the day. Refineries, chemical plants and pipe fabricators hire them to witness welder qualification tests, check fit up and preheat on code piping, and sign off visual inspection before radiography or ultrasonic testing. Expect $700 to $1,100 per 10 hour day, plus per diem of $100 to $200 when the job is away from home, and a minimum of several days for a turnaround. Welder qualification witnessing is often priced per test, around $150 to $400 per welder plus the lab bend tests. If the code also asks for volumetric NDT on the same welds, compare the per weld prices in our radiographic testing cost breakdown and see how crews scope girth welds on our pipe weld testing page.

Does the credential change the price?

A little. An AWS CWI alone is the common credential for fabrication, pipe and plant work. Building departments often require ICC Structural Welding (S2) or Structural Steel and Bolting (S1) certification for special inspectors, and inspectors who hold both CWI and ICC credentials usually sit at the top of the hourly range. A Senior CWI or an inspector who also holds UT Level II can save a separate trip, because one person covers both tasks. Check what your building official accepts before you compare quotes, since the cheapest inspector is useless if the report is rejected. The inspection and test rules for steel are in IBC Chapter 17.

What to send for comparable CWI inspection quotes

  • The statement of special inspections, with each task marked continuous or periodic, or the owner's weld inspection specification on plant work.
  • Risk Category and seismic design category, which set the UT rate on CJP welds.
  • Steel tonnage, connection count and an estimate of CJP and fillet weld quantities.
  • Fabricator name, location and whether it is AISC certified.
  • Erection schedule, shifts, weekend work and the notice period for call outs.
  • Required credentials: AWS CWI, ICC S1 or S2, UT Level II to AWS D1.1 Clause 8.
  • Who pays for reinspection after a rejected weld.
  • Deliverables: daily reports, deficiency log with photos and the final letter.

How much does a CWI charge per hour?

Most US agencies bill a CWI at $75 to $125 per hour at straight time, with overtime and weekend work at 1.5 times that rate. Expect a 2 to 4 hour minimum per visit plus mileage, so a short call out often costs $200 to $550 even when the inspection itself takes half an hour.

How much does a CWI cost per day?

On plant, pipe and shutdown work a CWI usually costs $700 to $1,100 per 10 hour day, plus per diem of $100 to $200 when the job is away from home. On building projects with continuous CJP weld inspection, an 8 hour day at hourly rates lands near $600 to $1,000.

Who pays for the welding inspector on a building project?

The owner or the owner's agent pays the special inspector under IBC Section 1704.2, because the inspector must be independent of the contractor. The steel contractor usually pays for repair and reinspection visits caused by rejected welds. Put both rules in the contract before erection starts so there is no dispute later.

Is a CWI the same as a special inspector?

Not always. A CWI is the AWS weld inspection credential. A special inspector is the person the building official accepts to perform code inspections, and many jurisdictions require ICC certification in addition to, or instead of, CWI. Ask your building department which credential it accepts before you hire.

How can I lower CWI inspection costs?

Group periodic tasks into planned visits, give 24 hour notice, sequence field CJP welding on consecutive days and use an AISC certified fabricator so shop inspection can be waived. Reducing weld rejections through preheat and welder discipline cuts repair visits, which are often the most avoidable line on the invoice.